WOODEN-IT-BE-NICE

Stephen M. Jornov - Owner/Craftsman

ALL ITEMS ARE CUSTOM MADE TO ORDER. THEY ARE MADE TO THE SIZE REQUESTED AS WELL AS THE WOOD DESIRED AND ANY INTERIOR OR EXTERIOR TREATMENT REQUIREMENTS.

**************************************************************************************************************************************************************

HOME BAR: Home Bar was constructed from Knotty Pine Boards and is 19" Deep x 48" Wide x 42" High. top was made from 2" thick Reclaimed Pine barn wood and has Four Coats of Semi-Gloss Polyurethane applied. Right Side has a drawer and Door with adjustable shelf inside.

Price -   $ 700.00 to $ 800.00

MAKEUP VANITY: The Vanity is constructed from 1/2"" Birch Plywood. and is 48" Long x 30" High x 24" Deep. The top Drawers are 6" High and the Bottom Drawers are 10" High

The Middle section is also 6" Deep and has a Flip up Top with a Mirror attached . 

The Legs are slightly tapered.

The Handles are 3/4" Square Satin Stainless Steel approximately 7" Long with a 1-1/4" projection.

The Stain is General Finished "EXPRESSO" and the Finish is three coats of Semi-gloss Polyurethane.

The below listed Stool was made as part of the set.

Price:       $ 900.00 - $ 1,000.00

MAKEUP VANITY Stool: The Stool is 18" Sq x 16" High with a 2" thick Upholstered Seat. The Seat has an Upholstered Welting between the Seat and Frame. Leg are slightly tapered.

Stain is General Finishes "EXPRESSO" and the Finish is three coats of Semi-Gloss Polyurethane.

Price: $ 250.00 - $ 300.00

OAK HALL TREE

This is a reproduction of an Antique Oak hall tree to match a customers possession. It is 68" Tall with 4 pedastal type legs that extend out 12" from the Upright. Legs are approximately 8" High. It is made from Straight grained Red Oak with a Golden Oak Stain. Finish is Four coats of sprayed on Semi-Gloss Water based Polyurethane.

Customer is installing Hanger /Hooks

Price: $ 250.00

Base for Hall Tree

Close-up of design for Hall Tree support legs and braces.

Jelly Cuboard

Cuboard is 24" wide x 12-3/4" deep x 73" high and is made from Maple Plywood and Solid Maple Face Frames. The shelves are fully adjustable every 1-1/4". Top has a crown molding and the back is a beadboard panel. Stained with Spanish Oak and finished with three coats of sprayed Gloss water based Polyurethane.

Price: $ 275.00 - $ 300.00

Ladderback Chair (Prototype)

Chair is 38" High x 17" deep x 17" Wide and was built from Poplar which was then Ebonized. Back slats are Curved and are made from Clear White Pine. Seat is cushioned and has been covered in cloth. Chair can be made from any wood and seat can be covered in your choice of materials. Finish is Three coats of Semi-gloss water based Polyurethane.

Price: $ 275.00 - $ 300.00 @ and 5% reduction on a set of 6 to 8 chairs

Side View of Ladderback Chair

Side view of ladderback chair showing curve of the bach support and the taper on the legs.

Coffee Table

Table is made from a section of Parquet flooring out of a 100 yr old house. Legs and support frame are made from ASH and the frame around the table is Walnut with a slight bevel on the outside edge. Top is covered with a glass panel.

Price: $ 400.00 - $ 450.00

End Table

Table is made from a section of Parquet flooring out of a 100 yr old house. Legs and support frame are made from ASH and the frame around the table is Walnut with a slight bevel on the outside edge. Top is covered with a glass panel.

Price: $ 275.00 - $ 300.00

Folding Picture Display Screen

Screen is made from Pine with a Golden Oak stain and two coats of sprayed Semi-Gloss Polyurethane. Screen is 42' Wide x 72" High.

Frames were sized to hold 8" x 11" pictures and pictures are easily changeable from the back side, Each frame panel is hinged with three foldng screen hinges. Can be custom designed to hold any size picture and can be made from any wood desired.

Price: Will depend on size of Screen and wood selected